Advanced signal integrity for high-speed digital designs

A synergistic approach to signal integrity for high-speed digital design This book is designed to provide contemporary readers with an understanding of the emerging high-speed signal integrity issues that are creating roadblocks in digital design. Written by the foremost experts on the subject, it l...

Descripción completa

Detalles Bibliográficos
Autor principal:	Hall, Stephen H. (-)
Otros Autores:	Heck, Howard L.
Formato:	Libro electrónico
Idioma:	Inglés
Publicado:	Hoboken, N.J. : John Wiley & Sons 2009.
Edición:	1st edition
Materias:	Digital electronics. Logic design. Signal integrity (Electronics)
Ver en Biblioteca Universitat Ramon Llull:	https://discovery.url.edu/permalink/34CSUC_URL/1im36ta/alma991009627634206719

Tabla de Contenidos:

Preface
Acknowledgments
Chapter 1: Introduction: The importance of signal integrity
1.1 Computing Power: Past and Future
1.2 The problem
1.3 The Basics
1.4 A new realm of bus design
1.5 Scope
1.6 Summary
1.7 References
Chapter 2: Electromagnetic Fundamentals for Signal Integrity
2.1 Introduction
2.2 Maxwell's Equations
2.3 Common Vector Operators
2.4 Wave Propagation
2.5 Electrostatics
2.6 Magnetostatics
2.7 Power Flow and the Poynting Vector
2.8 Reflections of Electromagnetic Waves
2.9 References
2.10 Problems
Chapter 3: Ideal Transmission Line Fundamentals
3.1 Transmission Line Structures
3.2 Wave propagation on loss free transmission lines
3.3 Transmission line properties
3.4 Transmission line parameters for the loss free case
3.5 Transmission line reflections
3.6 Time domain Reflectometry
3.7 References
3.8 Problems
Chapter 4: Crosstalk
4.1 Mutual Inductance and Capacitance
4.2 Coupled Wave Equations
4.3 Coupled Line Analysis
4.4 Modal Analysis
4.5 Crosstalk Minimization
4.6 Summary
4.7 References
4.8 Problems
Chapter 5: Non-ideal conductor models for transmission lines
5.1 Signals propagating in an unbounded conductive media
5.2 Classic conductor model for transmission lines
5.3 Surface Roughness
5.4 Transmission line parameters with a non-ideal conductor
5.5 Problems
Chapter 6: Electrical properties of dielectrics
6.1 Polarization of dielectrics
6.2 Classification of dielectric materials
6.3 Frequency dependent dielectric behavior
6.4 Properties of a physical dielectric model
6.5 The fiber-weave effect
6.6 Environmental variation in dielectric behavior
6.7 Transmission line parameters for lossy dielectrics and realistic conductors
6.8 References
6.9 Problems
Chapter 7: Differential signaling
7.1 Removal of common mode noise
7.2 Differential Crosstalk
7.3 Virtual reference plane
7.4 Propagation of Modal Voltages.
7.5 Common terminology
7.6 Drawbacks of differential signaling
7.7 References
7.8 Problems
Chapter 8: Mathematical Requirements of Physical Channels
8.1 Frequency domain effects in time domain simulations
8.2 Requirements for a physical Channel
8.3 References
8.4 Problems
Chapter 9: Network Analysis for Digital Engineers
9.1 High frequency voltage and current waves
9.2 Network Theory
9.3 Properties of Physical S-parameters
9.4 References
9.5 Problems
Chapter 10: Topics in High-Speed Channel Modeling
10.1 Creating a physical transmission line mode
10.2 Non-Ideal Return Paths
10.3 Vias
10.4 References
10.5 Problems
Chapter 11: I/O Circuits and Models
11.1 Introduction
11.2 Push-Pull Transmitters
11.3 CMOS Receivers
11.4 ESD Protection Circuits
11.5 On-Chip Termination
11.6 Bergeron Diagrams
11.7 Open Drain Transmitters
11.8 Differential Current Mode Transmitters
11.9 Low Swing/Differential Receivers
11.10 IBIS Models
11.11 Summary
11.12 References
11.13 Problems
Chapter 12: Equalization
12.1 Introduction
12.2 Continuous Time Linear Equalizers
12.3 Discrete Linear Equalizers
12.4 Decision Feedback Equalization
12.5 Summary
12.6 References
12.7 Problems
Chapter 13: Modeling and Budgeting of Timing Jitter and Noise
13.1 The Eye Diagram
13.2 Bit Error Rate
13.3 Jitter Sources and Budgets
13.4 Noise Sources and Budgets
13.5 Peak Distortion Analysis Methods
13.6 Summary
13.7 References
13.8 Problems
Chapter 14: System Analysis Using Response Surface Modeling
14.1 Introduction
14.2 Case Study: 10 Gb/s differential PCB interface
14.3 RSM Construction by Least Squares Fitting
14.4 Measures of Fit
14.5 Significance Testing
14.6 Confidence Intervals
14.7 Sensitivity Analysis and Design Optimization
14.8 Defect Rate Prediction Using Monte Carlo Simulation
14.9 Additional RSM Considerations
14.10 Summary.
14.11 References
14.12 Problems
Appendix A: Useful formulae, identities, units and constants
Appendix B: 4-port Conversions between T and S-parameters
Appendix C: Critical values of the F-statistic
Appendix D: Critical values of the t-statistic
Appendix E: Derivation of the internal inductance using the Hilbert Transform.

Advanced signal integrity for high-speed digital designs

Ejemplares similares